This firewall blocks incoming connections. For certain online gaming and applications you may need to open a port. This process of opening a port is frequently called a port forward , since you are forwarding a port from the Internet to your home network. I will show you how to: setup a static IP address on the device you plan on forwarding these ports to. We think that forwarding a port should be easy. Our software does everything that you need to forward a port.
|Published (Last):||19 February 2007|
|PDF File Size:||3.13 Mb|
|ePub File Size:||8.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co. Page 5: Safety Precautions Avoid collision during storage, transportation and operation of the equipment. Without prior written consent from Huawei, no company or individual is allowed to decompile, disassemble, modify or reverse engineer the equipment and shall be solely responsible for any effect resulted from such action.
Page 6 The temperature of the equipment shell goes up when used for long hours. This is a normal phenomenon. Cleaning: Before cleaning the equipment, turn off the equipment and unplug the power supply. Clean the equipment shell with a piece of soft cloth. Do not spray liquid onto the equipment, to avoid damage to the internal circuit. Page 8 3. Data, video and audio are transmitted through the common telephone line at a higher rate by the HGs.
Page Rear Panel 1. Page 13 same telephone line at the same time, you need an external splitter to separate the voice and data signals: LINE: Connecting to the phone jack on the wall. Before installing the HGs, make sure that your computer is equipped with the network card 2. Connect the interfaces of the splitter with the corresponding equipment by using the telephone line.
Connect the LINE interface of the splitter with the telephone jack on the wall. Page Establishing Configuration Environment 2. This section describes the process to establish the configuration environment of the HGs. Table Parameters for the configuration environment Name Description Default The process to unselect this function is described as follows taking Internet Explorer 6.
Page 18 Configuration area: It is on the right side of the page. In the service configuration of the HGs, you need to configure parameters, for example, the permanent virtual channel PVC. Page 21 when you select a service mode. Table lists the service modes of the HGs. Follow the prompt in the configuration page to perform this operation.
Configuring your computer After completing the configuration of the HGs, you need to install the PPP dial-up software to access the Internet. Enter the username and password. Then click Next. For the procedure, refer to 2. Click Submit. Configuring Your Computer Configure the network card for your computer, to enable the computer to automatically obtain information such as the IP address and the gateway.
Page Configuring The Rfc ipoa Mode 3. For details, refer to 3. Then Click Submit. The username and the password of the HGs are configured by default. To change the administrator password, follow the steps: Log in to the Web configuration page of the HGs. Page 38 1. Using the Reset button Follow the steps: Find the Reset button in the rear panel of the HGs Use a pin to press the Reset button and then release it after 3 seconds. Page Chapter 5 Troubleshooting Chapter 5 Troubleshooting 5.
The Power Ensure that the HGs is connected to the power indicator is not on supply properly. Ensure that the Power button is pressed. Ensure that the ADSL line is connected properly. Page Faqs Problem Solution Ensure that all the previous problems are addressed. Otherwise, restore the default settings. Ensure that the dial-up software is correctly installed and set properly on your computer. The Internet Ensure that you have entered the right username cannot be What to do if the username and the password of the Web configuration page are forgotten?
If the username and the password of the Web configuration page are forgotten, configure the HGs to the default factory settings. Use the default username and password to access the Web manager.
Page Chapter 7 Appendix Chapter 7 Appendix 7. Mode Bridge Bridge Bridge Bridge
Easiest Way to Get an Open Port on the Huawei EchoLife HG520s Router
Huawei EchoLife HG520s User Manual