Kale Control mode change- Select control at speed detection error over during speed Page of Go. Drive Parameter gw mode: B Torque bias 1 setting Refer to section for details on selecting the torque bias 1 setting. Customising Block-b,c Parameter Chapter 7 Options 7. Control Functions and Parameter Settings B Torque setting Refer to section for details on selecting the torque setting. Read this manual thoroughly before using the VAT, and store in a safe place for reference.
|Published (Last):||13 September 2009|
|PDF File Size:||1.10 Mb|
|ePub File Size:||4.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is possible to use any analog input either as setting or feedback. Increase the acceleration time setting A The following is an example for reading the output current as a percentage and then vah the output frequency as Hz. Table of Contents Add to my manuals Add.
VAT O pe n collecto r M ax. The Z-phase pulse is the zero point position detection and is used only for PM motor control. Programmable Sequence Output Function pso 5. Look for the noise source and remove the cause. The VAT stops with this signal turned off. Options 8 ,5 L a b e l M 1 0 Foot-Print filters Stand Alone Filters 3 Recommended Installation instructions for Electro Magnetic Compliance An inverter has not intrinsic on its own, but is considered as a component to be installed with other control components.
The operation starts from the run speed and operation time vzt when the operation was previously stopped. Built in dynamic braking up to 7. The mode or block displayed will change each time when the key is pressed. This will affect the current response. The output frequency or motor speed is the target for comparison. Page 3 Refer to section 1 and set the parameters B to 3. A short circuit in the load may have occurred. One of the three types of inputs can be selected by setting a parameter or with the sequence input.
Autotuning do this automatically. Note 7 An output voltage exceeding the input voltage cannot be attained. Got it, continue to print. Stop Frequency speed The base speed is 1. When using the 2-phase pulse, the rotation direction is judged by the advance and delay of the 2-phase pulse.
OFF The drive starts when run command is given after pre-charging. Page 81 This will affect the current response. With the VAT, the encoder pulse is defined as shown below during forward run. All trademarks are acknowledged. Test Operation and Adjustment Test operation with operation panel The test operation with the operation panel is performed with the following procedure.
Page 58 For stoppage, either ramp down stop or coast-stop is available. Built-in Pcb Option B Torque bat 1 setting Refer to section for details on selecting the torque ratio 1 setting. VAT automatic tuning can be carried out independently for each of bat following types of control. Is possible to set the number of retries, and the wait time t. Output ferrite choke also may be installed gat the motor power cables p Install the inverter in a metallic earthed cabinet.
Check the signal wiring. Preface Also make sure that this manual is delivered to the final users. Control Functions and Parameter Settings C Overspeed protection level This parameter set the overspeed protection level, as a percentage in respect to the maximum frequency B or maximum speed B This value can be set from either serial communication or through the Operation panel this allows two different settings.
Power Drive Services
It is possible to use any analog input either as setting or feedback. Increase the acceleration time setting A The following is an example for reading the output current as a percentage and then vah the output frequency as Hz. Table of Contents Add to my manuals Add. VAT O pe n collecto r M ax. The Z-phase pulse is the zero point position detection and is used only for PM motor control.
Kigahn Changes to the Utility Mode. Flow Of Test Operation 3. Sensor mode uses a encoder fited on motor shaft to feedback the real motor speed. To print the manual completely, please, download it. Selection Of Operation Mode Maintenance and Inspection Troubleshooting with fault display The countermeasures for when the inverter stops with a fault code display are shown in Table Precautions For Safety Precautions For Safety Precautions For Safety Items to be observed to prevent physical damage and to ensure safe use of this product are noted on the product and in this instruction manual.
- GOLDBLATT TOPOI PDF
- DATAHANDLER MIME TYPE PDF
- HUMAX 5400 MANUAL PDF
- HAVE YOU SEEN THE ONE I LOVE POPE SHENOUDA PDF
- BOILER OPERATOR HANDBOOK HESELTON PDF
- MANUAL DO DIREITO COMERCIAL FABIO ULHOA COELHO PDF
- EAW KF760 PDF
- COURS DE MICROCONTROLEUR PIC 16F84 PDF
- A COURSE IN DIFFERENTIAL GEOMETRY THIERRY AUBIN PDF